[HTML][MySQL][PHP] Apache2 i php próbuje ściągać zamiast wykonywać plik Opcje

[AdrianT]

Witam
Szanowni Państwo
Od kilku dni próbuję zainstalować Apache2, php5, mysql i próbuję to zmusić do współpracy (ze mnę oczywiście). Pewnie byłoby całkiem dobrze gdyby nie fakt, iż próba wykonania dość zaawansowanego skryptu typu:
<?php phpinfo(); ?>
kończy się próbą ściągnięcia zamiast wykonania pliku. Temat ten jet dość stary i dość obszernie opisany na forach jednakże nie bardzo mi się udaje z tym wygrać. Przez te kilka dni udało mi się przeglądnąć n-set stron a nawet próbować modyfikować pliki. Żadne z tych czynności nie przyniosły rezultatu. W chwili obecnej zdecydowałem się zapytaći prosić Państwa o pomoc w rozwiązaniu problemu. Całość została odinstalowana i powtórnie zainstalowana aby ...nie było zbytnio namieszane i można było się czegoś czepić.
Zapytacie mnie zapewne o to czy serwer Apache2 jest włączony: Tak - jest włączony.
Wynik działania polecenia

service apache2 status

jest poniżej

● apache2.service - LSB: Apache2 web server
Loaded: loaded (/etc/init.d/apache2)
Active: active (exited) since wto 2016-08-09 15:18:36 CEST; 9s ago
Process: 2368 ExecStop=/etc/init.d/apache2 stop (code=exited, status=0/SUCCESS)
Process: 2377 ExecStart=/etc/init.d/apache2 start (code=exited, status=0/SUCCESS)

sie 09 15:18:36 debian apache2[2377]: Starting web server: apache2(98)Address already in use: AH00072: make_sock: could not bind to ... [::]:80
sie 09 15:18:36 debian apache2[2377]: (98)Address already in use: AH00072: make_sock: could not bind to address 0.0.0.0:80
sie 09 15:18:36 debian apache2[2377]: no listening sockets available, shutting down
sie 09 15:18:36 debian apache2[2377]: AH00015: Unable to open logs
sie 09 15:18:36 debian apache2[2377]: Action 'start' failed.
sie 09 15:18:36 debian apache2[2377]: The Apache error log may have more information.
sie 09 15:18:36 debian apache2[2377]: .
Hint: Some lines were ellipsized, use -l to show in full.

„ Action 'start' failed” - zakładam że jak pracuje to powtórne wystartowanie nie da pozytywnej odpowiedzi.
Kolejne pytanie Państwa może dotyczyć pliku httpd.conf i jego modyfikacji: nie mam takiego(albo nie umiem go znaleźć – find / -iname httpd.conf ) , mam natomiast php5.config

<FilesMatch ".+\.ph(p[345]?|t|tml)$">
SetHandler application/x-httpd-php
</FilesMatch>
<FilesMatch ".+\.phps$">
SetHandler application/x-httpd-php-source
# Deny access to raw php sources by default
# To re-enable it's recommended to enable access to the files
# only in specific virtual host or directory
Require all denied
</FilesMatch>
# Deny access to files without filename (e.g. '.php')
<FilesMatch "^\.ph(p[345]?|t|tml|ps)$">
Require all denied
</FilesMatch>

# Running PHP scripts in user directories is disabled by default
#
# To re-enable PHP in user directories comment the following lines
# (from <IfModule ...> to </IfModule>.) Do NOT set it to On as it
# prevents .htaccess files from disabling it.
<IfModule mod_userdir.c>
<Directory /home/*/public_html>
php_admin_flag engine Off
</Directory>
</IfModule>



oraz plik apache2.conf (wyrzuciłem opisy z początku pliku bo był za długi)

# This is the main Apache server configuration file. It contains the
#.
#.
#.

# Global configuration
#

#
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
#
# NOTE! If you intend to place this on an NFS (or otherwise network)
# mounted filesystem then please read the Mutex documentation (available
# at <URL:http://httpd.apache.org/docs/2.4/mod/core.html#mutex>);
# you will save yourself a lot of trouble.
#
# Do NOT add a slash at the end of the directory path.
#
#ServerRoot "/etc/apache2"

#
# The accept serialization lock file MUST BE STORED ON A LOCAL DISK.
#
Mutex file:${APACHE_LOCK_DIR} default

#
# PidFile: The file in which the server should record its process
# identification number when it starts.
# This needs to be set in /etc/apache2/envvars
#
PidFile ${APACHE_PID_FILE}

#
# Timeout: The number of seconds before receives and sends time out.
#
Timeout 300

#
# KeepAlive: Whether or not to allow persistent connections (more than
# one request per connection). Set to "Off" to deactivate.
#
KeepAlive On

#
# MaxKeepAliveRequests: The maximum number of requests to allow
# during a persistent connection. Set to 0 to allow an unlimited amount.
# We recommend you leave this number high, for maximum performance.
#
MaxKeepAliveRequests 100

#
# KeepAliveTimeout: Number of seconds to wait for the next request from the
# same client on the same connection.
#
KeepAliveTimeout 5


# These need to be set in /etc/apache2/envvars
User ${APACHE_RUN_USER}
Group ${APACHE_RUN_GROUP}

#
# HostnameLookups: Log the names of clients or just their IP addresses
# e.g., www.apache.org (on) or 204.62.129.132 (off).
# The default is off because it'd be overall better for the net if people
# had to knowingly turn this feature on, since enabling it means that
# each client request will result in AT LEAST one lookup request to the
# nameserver.
#
HostnameLookups Off

# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
#
ErrorLog ${APACHE_LOG_DIR}/error.log

#
# LogLevel: Control the severity of messages logged to the error_log.
# Available values: trace8, ..., trace1, debug, info, notice, warn,
# error, crit, alert, emerg.
# It is also possible to configure the log level for particular modules, e.g.
# "LogLevel info ssl:warn"
#
LogLevel warn

# Include module configuration:
IncludeOptional mods-enabled/*.load
IncludeOptional mods-enabled/*.conf

# Include list of ports to listen on
Include ports.conf


# Sets the default security model of the Apache2 HTTPD server. It does
# not allow access to the root filesystem outside of /usr/share and /var/www.
# The former is used by web applications packaged in Debian,
# the latter may be used for local directories served by the web server. If
# your system is serving content from a sub-directory in /srv you must allow
# access here, or in any related virtual host.
<Directory />
Options FollowSymLinks
AllowOverride None
Require all denied
</Directory>

<Directory /usr/share>
AllowOverride None
Require all granted
</Directory>

<Directory /var/www/>
Options Indexes FollowSymLinks
AllowOverride None
Require all granted
</Directory>

#<Directory /srv/>
# Options Indexes FollowSymLinks
# AllowOverride None
# Require all granted
#</Directory>




# AccessFileName: The name of the file to look for in each directory
# for additional configuration directives. See also the AllowOverride
# directive.
#
AccessFileName .htaccess

#
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
#
<FilesMatch "^\.ht">
Require all denied
</FilesMatch>


#
# The following directives define some format nicknames for use with
# a CustomLog directive.
#
# These deviate from the Common Log Format definitions in that they use %O
# (the actual bytes sent including headers) instead of %b (the size of the
# requested file), because the latter makes it impossible to detect partial
# requests.
#
# Note that the use of %{X-Forwarded-For}i instead of %h is not recommended.
# Use mod_remoteip instead.
#
LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined
LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %O" common
LogFormat "%{Referer}i -> %U" referer
LogFormat "%{User-agent}i" agent

# Include of directories ignores editors' and dpkg's backup files,
# see README.Debian for details.

# Include generic snippets of statements
IncludeOptional conf-enabled/*.conf

# Include the virtual host configurations:
IncludeOptional sites-enabled/*.conf

# vim: syntax=apache ts=4 sw=4 sts=4 sr noet


Gdzie popełniam błąd i dlaczego to nie działa
Serdecznie dziękuję za pomoc